How To Change Code On Door Lock Weiser

Please install one smart door lock at a time. The bolt should retract to the unlocked position.

Weiser 9GLA14900002 Smartcode Smartkey Handleset with

Locked turnbutton the turnbutton cannot rotate.

How to change code on door lock weiser. Page 6 62816 / 01 troubleshooting: Code to teach the lock the orientation of the door: Using the weiser app within bluetooth range, you can lock/unlock the aura smart lock and program up to 250 user access codes that can be scheduled and.

Once the smart door lock has been physically installed and tested for proper functioning, follow the steps below to pair your smart door lock with your rogers smart home monitoring system. Switch #2 enables the auto lock when in the on position. Line up the connecting rods and cylinder tailpiece to insert the interior trim.

Hope this helps, i'd been wondering about it myself for a lonnngg time :) Enter user code to be deleted. Test the old user code to make sure it can no longer unlock the door.

Procedure continued on next page 4 / 15 62810 / 01 usa: Insert the key into the lock and turn it slightly more than half a turn while pulling the cylinder tailpiece through the back of the lock. Enter the code to unlock:

If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock. The door can be locked with the lock button, but the user code will not unlock the door. Door drilling instructions available at www.weiserlock.com/doorprep.

Pair the smart door lock to your rogers smart home monitoring system using this guide. Press the “lock” button to save code. 3 enter user code to be deleted.

Enter the access code to unlock: Hold these two units in place, then insert screws into the interior side of the lock to fasten it to the door. 38 mm (1 1/2 in).

Smartcode at a glance deleting a single user code Programming the 2nd user code. With auto lock enabled, smartcode will automatically relock the door

Find all the resources to help with your weiser product and installation needs. 2 press lock button once. If you have an old weiser lock that does not have the smart key feature, you'll have to remove the lock from the door to rekey it.

If drilling a new door, use the supplied template and the complete. If you're looking for answers, information and resources to help. Press the program button once more.

This process will only work if your weiser lock is installed on the door and the door is shut. To start over, touch the lock button to lock the door. If unsuccessful make sure to enter the same valid code in steps 3 and 5.

Door jammed while attempting to lock relock door. Press the 1 button and wait for the same three lights and three beeps. Wait a moment for the three lights and three beeps to repeat.

Smart door lock (weiser smartcode 10 touchpad electronic deadbolt) 2. The door is either 54 mm (2 1/8 in) or. Test code while the door is open, test the user code to make sure it no longer unlocks the door.

Enter in 4 to 8 digit code onto the keypad. 4 press lock button once. Call technical support for further troubleshooting.

You should see the schlage button turn green, giving one long flash and one long beep. 6 press lock button once. Prepare the door and check dimensions.

Fl ashes green (about 5 seconds). Fl ash fi ve times and you will hear fi ve beeps. Make sure the user code is correct and that the lock button is pushed after entering the user code.

No user code programmed program at least one user code ©2014 weiser corporation important safeguards 1 2 3 remove battery pack. Press and hold the program button until the keypad 4. Enter in 4 to 8 digit code onto the keypad.

Keep holding the button for 30 seconds until the lock beeps Insert the exterior (keyed) side of the lock through the exterior side of your door. For example, if you want to delete the third code, add a diff erent user code in position three.

Press the program button twice, enter the same or a new code and then press the lock button once. If the door still won’t unlock, use a key to unlock the door. If it does not unlock, repeat steps (a) through (c).

This is something most homeowners quite often forget to do. Consequently, how do you change the code on a kwikset door lock? Pair with smartthings [found information on how to put the lock into pairing mode by following [ref 4] pairing the smart door lock with your touchpad”]

Reference guide exterior back panel. If your old code still remains in the unit, you will need to perform a hard reset of the unit. Just pull off the top back cover of the unit and you will find the simple step by step instructions on how to change the combination on the inside of the cover.

When the door is closed and the lock. Press the program button once. When the led flashes green, the lock has been reset.

Manufacturer’s installation guide important installation steps 1. Press and hold the program button while reinserting the battery pack. Page 5 62812 / 01 deleting a single user code with the mastercode enabled 1.

Remove the existing door lock. Man installing a door lock on a white door. The full screen is now revealed.

Press the “lock” button to save code. After typing in the last 4 digits of your phone number click change lock code and type in the new lock code you would like. On the touchpad, select the settings app from the home screen.

The door is now unlocked! Measure to con irm that the hole in. The lock beeps, the keypad ﬂ ashes red, and the door cannot lock or unlock.

Press the program button on the interior unit three times. Install the smart door lock using the manufacturer’s installation guide provided in the box. For instuctions on how to add user codes when the mastercode is disabled, see the installation and user guide that came with your lock.

Just go through all the possible combinations and unlock it (only if its a 3/4 digit) on the other hand if you do know the code and want to change the lock, hold down the unlock button/lever and change the digits and that should change the code.

Get the Weiser Lock Iron Black Round Pocket Door Privacy